Share your bras and experiences and help other women
Get recommendations, write review and learn more!

Got bras? Create an account

Bras » Unknown Brand » Size range » 38B » Reviews

Unknown Brand

  1. Unknown Model

    0
    like

    38B

    Hasn't set fit

    Ewe, Ewe, Ewe!!!! Lookie what I found!! I bought this at a thrift store Wednesday morning for $4!! It is a Charlotte Russe. : )

    Updated on Feb 05, 2015 Flag this


    • Show all comments (20)
    • 2

      Do they fit?

    • 1

      dbmamaz Thanks! :) I think so, but not quite yet. They both seem to be a fit but they need some work:

      I need to get the lace reworked on the back of the Charlotte Russe, and i think it will be fine.

      The Forever 21 has a zipper that I need to figure out how to get closed with the tension on it. It has an elastic panel in the back.

    • 2

      I'm not sure exactly what the picture is of, sort of looks like part of the laces found in corsets...?

    • Yes,valentine556 I will retake pictures. Jj rejected my pictures, I think because I photographed them both together?

    • 1

      Yeah, that's probably why, you have to take separate pics.

    • 1

      And I think that Charlotte Russe is the name of the brand, not the model :)

    • 1

      Yes, Scharminkeltje; they are both corselettes (?) without cups, so I didn't think it would matter. Ah, well, live and learn. I will take separate photos later today when I have time, and upload them.

      Yes, Charlotte Russe is the brand-name. I'll fix that too. :)

    • 1

      Now that I see the pics.... wowowowowowoowow it's pretty!

    • Thanks, Scharminkeltje I thought it was pretty sweet, especially for $4! :)

    • 1

      Very cute, it looks like you could even swap out the boning so that instead of plastic it has at least spiral if not spiral and spring/flat steel so that it actually cinches without needing to fear the moment that a plastic bone snaps and/or rips through the corset fabric.

      Fashion corsets have always been so disappointing for me, since they're often so beautiful yet nowhere near as strong as they need to be in order to create the "super dynamic hourglass" shape. :)

    • So, valentine556 Where does one acquire spiral and spring/flat steel to do a swap-out? Is it stainless?

    • Look up corset making supplies on google! :)

    • Thanks! :)

    • valentine556 So when you say using "spriral and spring/flat steel do you mean alternating between the two, or combining the two into each of the pockets?

    • It depends. The spring/flat steel are typically found in the boning channels closest to the grommets for the laces for stability reasons. The spiral steels are then used in the remainder of the boning channels. Fashion corsets with plastic boning generally make the torso look like a cylinder wrapped in pretty fabric. Not exactly what most have in mind when they buy a corset that's not adequate in structural design for any waist cinching. If there's no waist tape and it's not added after the fact, special care should be taken to not strain the corset structure with tight-lacing. Basically even with some upgrades there are limits to what one can or should expect from the corset - my guess is that it would be able to handle a 2" reduction but 4" on a regular basis will eventually - much sooner rather than later - kill the corset.

    • Ok, thank you valentine556! Now I'm understanding better! And the waste tape would run horizontally to reinforce the center? : )

    • Yes, however, adding waist tape to a corset will require figuring out how to do it without stitching through the boning channels - technically if the tape is only stitched down on the inside in the spaces between each channel it should be enough, but will be visible on the outside too unless you take the layers apart and that's even more complicated to put back together successfully. :) Might be better off getting a corset with the waist tape and steel bones for tighter lacing and the upgraded boning corset for lighter duty wear.

    • valentine556 OK, thanks for the info! I'll take a closer look at and do some pondering! : )

    • No problem! Good luck!

    • No problem! Good luck!

    add a comment

    Use @ to mention users, brands, models and more

    You need to sign in to comment